The Proman Saw Unit Model #110 mitre saw is a Swedish made suspension saw of exceptional quality. Of all the saws on the world market it is the only unit we are happy to recommend. The accuracy of the cut is fine enough to produce a quality mitre in black and fine gold leaf mouldings. The saw unit comes complete with one dual action moulding clamp, an inbuilt measuring stop, and one saw blade. Maximum cutting width and height at 45 degrees is 105mm or 4 1/4 inches. The maximum cutting length at 45 degrees depends upon the length of the measuring system.

There is usually no need to sand the mitres after cutting with the Proman saw.

The FrameCo Measuring System can be fitted to the Proman saw, which then allows lengths of moulding up to 168cm or 64 inches to be cut.. The unit can be disassembled for easy storage, or can be mounted onto a wood or metal base. This makes the unit more steady and the whole assembly can still be stored away when not in use.

The Proman saw is supplied with an 18TPI (teeth per inch) blade as standard. This blade is good for general framing, however a 24TPI blade gives a finer and more even cut. There is also a blade of 32 TPI which can be used for cutting aluminium frame mouldings.

The base table of the saw has grooves built into the cutting surface. These are used for cutting compound mitres, which can then be joined with the PushMaster and the PushMaster Compound Mitre Ring.

Recommended products to be used with the Proman Saw Unit:
- Ezy-Measure System ..combines with the saw for accurate frame cutting everytime Click for details/buy
- PushMaster/BenchMaster Joiners...for a superior v-nail joint Click for details/buy
- FrameCo Strap Clamp..pulls the mitres firmly together Click for details/buy
- Compound Mitre Ring...for creative joinery Click for details/buy
- Mitre Trimmer Guillotine. shaves the mitre for an even finer cut code: #10120 Proman Saw Model #110 - Complete Unit Click for details/buy

- Code: #10119 Proman Saw Replacement Blade - 18 TPI for Cross Cuts and Picture Framing Click for details/buy
- Code: #10121 Proman Saw Replacement Blade - 24 TPI finer blade for picture framing Click for details/buy
- Code: #10122 Proman Saw Replacement Blade - 32 TPI for metal cutting Click for details/buy

The Mitre Trimmer is an excellent addition to the home framers workshop. If you are currently cutting frame moulding with a power saw, or a cheaper quality suspension saw, then the mitres can be improved to near perfect by trimming them in the guillotine. The most acceptable method of cutting for the professional framer is with a Morso Guillotine... not power saws!! These guillotines have been on the market for over 50 years and produce a near perfect mitre. But for home use, they are not affordable . So the mitre Trimmer is a practical alternative, and they produce a better mitre than a disc sander. The Mitre Trimmer's super sharp, solid, hollow ground blades leave a clean, smooth cut. Use the Trimmer to shave off a thin piece of the timber to ensure an accurate 45° cut. First cut the moulding into 4 pieces approximately 5mm (1/4") longer than required. This will allow sufficient length to trim the ends for perfect joints every time.

The Trimmer will trim material up to 125mm (5") wide and 100mm (4") thick. Cuts many angles from 90 through to 45° and can be calibrated to ensure accurate mitre cuts. The Trimmer will cut all types of timber, including very hard woods. Blades can be re-sharpened many times over to maintain a quality cutting edge.

Ideal addition to any workshop, especially if your current power/manual saw is not cutting at exact 45°.

Recommended products to be used with the Mitre Trimmer Guillotine:
- Power Saws..the trimmer will improve any saw cut Click for details/buy
- PushMaster or BenchMaster Joiners...once the frame is cut, secure with a v-nail Click for details/buy
- FrameCo Strap Clamp..for strong, tight mitres Click for details/buy
- Code: #12000 Mitre Trimmer Guillotine Click for details/buy
- Code: #12002 Mitre Trimmer Blade Set Click for details/buy